Thông tin chi tiết sản phẩm:
|Tên sản phẩm:||Vỏ xoay||Đường kính lỗ khoan:||1000-2000mm|
|Mô-men xoắn quay:||2965/1752/990 kN.m Tức thời 3391 kN.m||Tốc độ quay:||1.0 / 1.7 / 2.9 vòng / phút|
|Hạ áp lực của tay áo:||Tối đa 600 kN + Trọng lượng chết 260 kN||Lực kéo của tay áo:||3760 kN, tức thời 4300 kN|
|Áp lực kéo Stroke:||750 mm||Trọng lượng:||46 tấn|
|Mô hình động cơ:||Cummins QSM11-335||Công suất động cơ:||272/1800 kw / rpm|
|Tiêu thụ nhiên liệu của động cơ:||216 g / kwh (công suất tối đa)||Chế độ điều khiển:||Điều khiển từ xa có dây|
|Trọng lượng của bộ nguồn:||8 tấn|
Casing Rotator KTR2005H and Hydraulic Power Pack
About Hydraulic Power Pack
We have the cutter head load automatic control system, when cutting the hard rock, it can well protect the cutter head and effectively enhance the cutting efficiency by the automatic control of computer.
We have the convenient operating system, according to the working condition the operating system platform of micro computer can keep the machine at an optimum working state by adjusting the speed, torque and pressing force, and promote the work efficiency to the maximum.
(1) No noise, no vibration, and high safety.
(2) Without mud, clean working surface, good environmental friendliness, avoiding the possibility for mud to enter the concrete, high pile quality, enhancing the bond stress of concrete to the steel bar;
(3) During construction drilling, the characteristics of stratum and rock can be directly distinguished;
(4) The drilling speed is fast and reaches about 14m/h for the general soil layer;
(5) The drilling depth is large and reaches about 80m according to the situation of soil layer;
(6) The hole forming verticality is easy to master, which can be accurate to 1/500;
(7) No hole collapse will be caused, and the hole forming quality is high;
(8) The hole forming diameter is standard, with little filling factor. Being compared with other hole forming methods, it can save a lot of concrete usage;
(9) The hole clearing is thorough and fast. The drilling mud at the hole bottom can be clear to about 3.0cm.
|Drilling Diameter||1000-2000 mm|
|Lower Pressure of sleeve||Max. 600kN+Dead Weight 260 kN|
|Pulling fore of sleeve||3760kN, Instantaneous 4300 kN|
|Pressure pulling stroke||750 mm|
|Parameters of Hydraulic power station|
|Engine Model||Cummins QSM11-335|
|Engine Power||272/1800 kw/rpm|
|Fuel Consumption of Engine||216 g/kwh( Max. power rate)|
|Control Mode||Wired remote control|
Use for different types construction:
(1) Foundation pile, continuous wall
Foundation piles for high-speed rail, road and bridge and house building;
Articulation pile constructions which are required to be excavated, such as subway platforms, underground architectures, continuous walls.
Water retaining wall of reservoir reinforcement.
(2)Drilling gravels, boulders and karst caves
It is allowable to conduct the foundation pile construction at mountain lands with gravel and boulder formations.
It is allowable to conduct operation and cast the foundation piles at the thick quicksand formation and necking down stratum or the filling layer.
Conduct rock-socketed drilling to the rock stratum, cast the foundation pile.
(3) Clear the underground obstructions
During the urban construction and bridge rebuilding, the obstructions such as the steel reinforced concrete pile, steel pipe pile, H steel pile, pc pile and wood pile can be cleared directly, and cast the foundation pile on the spot.
(4) Cut the rock stratum
Conduct the rock-socketed drilling to the cast-in-place piles.
Drill through-holes on the rock bed(shafts and ventilation holes).
(5) Deep excavation
Conduct the in-place casting or steel pipe pile inserting for the deep foundation improvement.
Excavate deep wells for construction use in the constructions of reservoir and tunnel.